How To Repair Pants Crotch

Download Commodity

Download Article

The crotch of your jeans is subject to all kinds of wearable and tear including stretching, thigh-rubbing, and horribly timed seam-splitting. It is the place most probable to get rips and tears, large and small-scale. Instead of throwing damaged jeans away in defeat, there are a number of methods you can utilize to fix a hole. A pocket-sized tear can be sewn together, while a larger hole will require patching. No matter how adept or bad you are with a needle and thread, you tin can ready a hole in the crotch of your jeans.

1
Cut loose threads away from the damaged area. You can set up some small holes without using a patch, but by sewing the sides of the pocket-sized hole or tear back together. Before y'all do this, yous should use some scissors to clean up the edges of hole and then there aren't any protruding loose threads. These will but make it the way equally y'all work. Exist careful not to make the hole any bigger as you do this.
- Merely cut frayed threads, non the bodily textile of the jeans.^[1]
two

Thread the needle and tie the knot properly . Placing a knot at the far end of the thread will anchor information technology in the fabric once you offset sewing. Information technology tin be frustrating to have to continue re-threading the needle, so exist sure to go the thread tightly fixed.

Advertisement
3
Stitch over the edges of the hole to prevent further fraying. Seal the edges of the damaged area past looping thread around them and "tying" them shut. Exist certain not to sew together so close to the border that the thread simply pulls more jean material loose. This step is optional, only it can assistance stop fraying around the hole and increase the forcefulness of your fix.
- A blanket stitch or buttonhole run up are good options for this.
4
Sew the gap in the wear shut. Press or concur the fabric so that the hole or tear in your jeans is nearly or completely shut. Then stitch vertically across the hole to shut it. (Annotation that yous may have to stitch over this more than than once to brand it tight.) Outset your stitches around a ½ inch to one side of the hole. Proceed them to around ½ inch past the other side of the hole.
- As you past the far-side of the pigsty, make the stitches gradually smaller.
- Pull the thread tight, necktie information technology off, and trim it so there are no loose ends.^[2]
- Starting time these stitches at least ½ inch further dorsum than the stitches you just used to seal the edges of the gap.
- You could also do this with a sewing machine, merely if it is a very pocket-sized hole, it could be just as easy to fix it past hand.
Advertisement

1

Cutting away the loose threads. Every bit with the method for sewing by mitt, the first thing to do is to clean upwardly the hole or rip past trimming abroad any loose or dangling threads. Take care every bit yous do this and try to exist every bit precise as possible.
two
Wind the bobbin on the sewing machine. Threading the needle on a sewing automobile can be a chip tricky as they use two sources of thread, one from the bobbin and i from the spool. The get-go affair to practice is current of air the bobbin so that it is wrapped with thread. Once the spool and bobbin are in place on the height of your machine, unravel a few inches of thread towards the far left side of the spool and wrap it effectually the nubbin on the left mitt side of your machine.^[3]
- Then pull this thread to the bobbin, thread it through the pocket-sized hole, and wrap it around the bobbin a few times to secure information technology.
- Ready the bobbin in place by pushing it to the correct and and so gentle printing down on your peddle to air current the thread from the spool to the bobbin until y'all have as much thread equally you need on the bobbin.
- Cut the thread to separate the spool and bobbin, so remove the bobbin and switch off your automobile.
3
Thread the spool. Take the end of the thread from the spool and pull information technology out to the left equally before. This time you are taking information technology downwardly to the needle itself. You volition take to have the thread through a hook on the top of the auto and down forth a aqueduct on the right manus side of the needle, before bringing information technology dorsum up to the meridian of the automobile through another aqueduct on the left, round the claw on the top and dorsum down the left channel.^[four]
- Thread the needle through the hooks on the front and side of the needle itself before finally threading it through the needle itself.
- They volition nigh probable be arrows or directions marked on your machine to make this easier.^[5]
- Most machine follow the same bones pattern for threading.^[vi]
4
Thread the bobbin. You have threaded the needle from the spool above, and at present it'south time to thread information technology from the bobbin below. Open up upwards your machine to reveal the bobbin holder below the needle, and remove the small metal bobbin holder. Place your threaded bobbin in the holder and pull a few inches of thread out through the slit in the side, earlier returning the holder to the car and closing it.^[7]
- To go the thread from the bobbin upward to the sewing surface, gently lower the needle with the hand wheel while holding the spool thread in your other hand.
- Bring the needle dorsum up, carefully pull on the spool thread and the bobbin thread should appear.^[8]
five

Seal the edges of the rip with a zig-zag sew. Centre a zig-zag sew together over the edge of the fabric (so that one-half of each stitch goes through the fabric the other half goes on the exterior to tie it close). Sew along each side of the hole to seal the edges and stop further fraying. Some sewing machines have a "buttonhole" setting or pedal that will work well for this purpose.
half dozen
Sew across the pigsty or tear to close it. Push together the two sides of the pigsty with your easily to close information technology. Once it is securely in position, agree information technology there and position information technology beneath the needle on your sewing machine. Then, sew vertically across the pigsty to bind information technology and close information technology. As with the sewing by hand method, exist certain to first and finish your stitches ½ inch on either side of the hole.
- If you sealed the edges of the tear first, make sure you showtime these new stitches ½ inch further dorsum to avert pulling out the before stitches.
- If the hole is in an specially tight or inconvenient spot, moving your jeans through the automobile may present a challenge and sewing past hand could exist easier.
Advertisement

1

Tidy up threads effectually the hole. Gluing on a patch is ideal for those who are not comfortable with a needle and thread, or just want a quick-fix. This might be a good option for piece of work jeans that are more of import to yous for their utility than their advent. As with the other techniques, the first affair to do is to cut away any loose threads to clean up the tear or hole.
2
Cut a patch to size. Turn your jeans inside out and measure out a piece of backlog denim from an quondam pair of jeans, or whatever you want to patch the hole with. Brand sure there is plenty of space on the patch around the torn expanse then yous can utilize the mucilage to the patch.
- You can buy fabric patches to use instead of a scrap piece.
3
Apply the textile mending glue to the patch. You should follow the specific instructions on given on the bottle, but mostly you will have to employ gum to the edges of the patch. Y'all will need to take care to ensure that you don't put mucilage on a part of the patch that is going to exist showing through on the outside of your jeans. Printing the patch down over the hole and secure information technology there.^[9]
- Different glues have different amounts of fourth dimension to dry out properly, but it shouldn't take more than a few hours.
Advert

i
Prepare the hole you are going to patch. Another easy alternative to sewing in a patch is to go an iron-on patch and apply that instead. As always, begin by cutting abroad excess threads so the hole is articulate, before turning your jeans within out and preparing the patch you are going to iron on to your jeans. Measure the hole with a tape measure out and cut the patch to size ensuring that there is a clearance of at least ½ inch around the hole.^[ten]
- You can measure this by middle, just by using a record measure, you are less likely to get it incorrect and end upward wasting a patch by cutting it likewise small.
- Cutting rounded corners on the patch will help forbid it peeling up.
two

Place a piece of scrap denim on the other side of the hole. Whether y'all are calculation the patch to the exterior or the inside of the jeans, using a scrap of denim on the contrary side to the patch will prevent the patch sticking to the other side of the jeans and potentially sticking the 2 sides together. This could seal your jeans shut and you might damage them if you then have to tear the leg open again.^[11]
3
Iron the patch. With a pre-heated iron you should now identify the patch over the hole and iron information technology down. How long you should do this for could depend on the particular atomic number 26-on patches you have, so be certain to read the instructions advisedly and follow those. Typically information technology won't exist for more than xxx-lx seconds.
- In one case information technology is set, remove the scrap slice from the opposite side and you are practiced to become.
Advertisement

ane
Find a patch or suitable patching material. Sewing in a patch is the virtually comprehensive, merely as well labour-intensive, manner to ready a larger pigsty in the crotch of your jeans. This requires some basic command of a needle and thread or sewing machine, but when done well it could be neater and more reliable than gluing or ironing on a patch. Begin by finding a patch for the hole in your jeans.
- If placing the patch on the interior, choose a colour that closely matches the colour of your jeans to arrive look more than natural.^[12]
- You can be creative with your patches if you want to make a statement or have some fun.^[13]
- Make sure the patch material isn't thicker than the cloth of your jeans. If it doesn't give when you motion, it will forcefulness the jeans to tear around it instead.
2

Cut out a patch at least 1 inch (2.5 cm) larger on all sides than the hole. If you lot're cutting the patch from a weave material (similar denim), cut diagonally against the weave; if you cutting straight along the criss or the cross of the weave, the edges volition be more likely to fray.
3
Place the patch over the hole, lay your jeans flat, and pin the patch to the jeans. Make sure there is no bunching or pulling or the patch volition end upwardly bulky and stressed. Unless you lot'd like to place a colourful or conspicuous patch over the damaged area, slide the patch into the interior of the jeans, which should be kept correct-side out.
- Some other option is to use an iron on patch. Instead of pinning information technology, y'all can iron information technology on and then sew it in for more than durability.
4

Sew in the patch with a sewing machine. Stitch around the perimeter of the hole, removing pins every bit you go. Don't stitch besides near the edges or the torn material will fray and the stitches will autumn out. Employ the auto's zig-zag stitch. You can as well use a straight stitch, but use a back and forth motion which will itself lend a zig-zag shape to the stitching.^[14].
five
Or sew it in by mitt. If y'all sew it in by paw utilise an overcast stitch. Poke the needle up through the patch nigh the edge. Plunge the needle and thread back down through the denim just outside the edge of the patch and somewhat forward from where your needle emerged, creating a unmarried diagonal run up. Once once again poke the needle up through the underside of the patch (near the edge and slightly forward) to create another diagonal sew on the underside of the material.
- Repeat until you've covered the entire perimeter of the patch in diagonal stitches. When y'all're done, do the unabridged procedure over once again just this fourth dimension, motion in the opposite direction to create diagonal stitches that cross the first ready yous made. The resulting effect volition expect like a cord of Xs.
- Be careful and make sure y'all are not sewing 2 sides of your jeans together, or sewing the textile from the inside of the pocket to the jean leg or crotch.^[15]
vi

Re-stitch effectually the perimeter of the hole if necessary. At present that the patch is firmly in place, you can also sew closer to the edges of the tear to concur information technology downwardly for a cleaner look. Re-sewing volition reinforce the force of the patch.^[16] But exist enlightened that adding layer upon layer of stitches can lead to your jeans becoming strong and uncomfortable.
7

Trim any loose edges. Once you lot have sewn in the patch, have some pinking shears or scissors and trim away any excess fabric from patch. This could flap around, itch, or catch on things that might loosen the stitches around your patch.^[17] Printing the stitches down with an iron to help smoothen out the stitches and your patching job is complete.

Advertisement

Add New Question

Question

How can I prepare a pigsty in my jeans without sewing?

David Pew is a Professional Tailor and the Possessor of Run up Generously based in Seattle, Washington. With over a decade of experience, David specializes in bespoke tailoring and alterations. He uses his experiences, skills, and centre for detail to produce the highest quality of products.

Professional Tailor

Expert Answer

You can gum the patch on with textile glue, but it won't be a permanent fix for your jeans.
Question

Practise you sew it on the inside?

Aye, get a needle and thread, sew on the inside of your jeans by turning them inside out.
Question

How tin can I fix my pants with glue?

Brand sure your pants are aligned correctly. Then y'all can use cloth or super glue to glue the hem (the border of the pants) where the hole is. Stick the ii sides of the fabric together and hold them for a few seconds until the glue has had a take chances to set.

Enquire a Question

200 characters left

Include your electronic mail address to get a bulletin when this question is answered.

Submit

Habiliment tight shorts or spankies under the pants y'all fixed just in example it rips again!
If y'all're using a sewing machine for the outset time, have it wearisome.

Advertising

Things Y'all'll Need

Sturdy sewing thread that matches (or compliments) the colour of your jeans.
A thick hand-sewing needle or a sewing auto.
Scissors or pinking shears.
If mending a big hole, a patch.
Iron (optional)
Fabric mending mucilage (optional)

Nearly This Article

Article Summary X

To fix a hole in the crotch of your jeans, brainstorm by cutting abroad any loose threads hanging from the tear so that they won't get in your mode every bit yous're sewing. So, thread a needle and necktie a strong knot at the stop of the thread. Run up around the edge of the hole with a blanket stitch to prevent the material from fraying fifty-fifty more. Once y'all've sewn around the edges of the hole, press it shut and sew across the hole to shut it. Afterward yous've sewn the hole shut, pull the thread tight and necktie a knot. Finally, trim the loose stop with pair of scissors. If you want to learn how to patch your jeans to set a larger pigsty, continue reading the commodity!

Did this summary help you lot?

Thanks to all authors for creating a page that has been read 980,582 times.

Did this commodity help yous?